Sealing adhesives
Klebt und dichtet Metalle und mehr
Der Kleb- und Dichtstoff ist metallisch glänzend. Nach der Aushärtung sehen Klebestellen und Fugen aus wie geschweißt.
Selbst ohne eine Oberflächenbehandlung mit Haftprimern wird eine hervorragende Haftung erreicht. Das Produkt ist nass auf nass anwendbar, überlackierbar und anstrichverträglich.
Nachdem der Kleb- und Dichtstoff abgebunden hat, bleibt er dauerelastisch und eignet sich somit hervorragend für Dehnungsfugen. Dies ist insbesondere bei Anwendung im Außenbereich wichtig, um beispielsweise Dehnungen und Spannungen von Boden- und Wandbelägen auszugleichen.
Egal ob regensaure Verwitterung, Salzwasser, Chlorwasser oder Haushaltsreiniger, das Produkt überzeugt mit hoher Beständigkeit und verfärbt sich nicht. Schmutz haftet praktisch nicht an und lässt sich jederzeit mühelos entfernen.
Durch die UV-Beständigkeit werden Fugenabdichtungen und Klebestellen nicht brüchig oder bröselig. Zudem ist der Kleb- und Dichtstoff beständig gegen extreme Kälte bis -40 °C und Wärme bis +100 °C.
Das Produkt ist resistent gegen Schimmel und Bakterien. Daher eignet es sich auch für den Einsatz unter feucht-warmen Umgebungsbedingungen.
Dieser Kleb- und Dichtstoff ist frei von Silikon, Lösemitteln und enthält keine Diisocyanate, die häufig Auslöser von Atemwegserkrankungen sind.
Free from MDI, Isocyanates, and Diisocyanates
This PU adhesive and sealant has been specifically developed to be free from Methylene diphenyl diisocyanate (MDI), isocyanates, or diisocyanates, which are often identified as triggers for respiratory diseases.
Unique Formula Identifier
- UFI: REX9-WXG7-RE9N-KFGD
Warning
Hazard statements
- H317 May cause an allergic skin reaction.
Precautionary statements
- P101 If medical advice is needed, have product container or label at hand.
- P102 Keep out of reach of children.
- P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
- P272 Contaminated work clothing should not be allowed out of the workplace.
- P280 Wear protective gloves/protective clothing/respiratory protection/eye protection/protective footwear.
- P302+P352 IF ON SKIN: Wash with plenty of water.
- P333+P313 If skin irritation or rash occurs: Get medical advice/attention.
- P501 Dispose of contents/container in accordance with local/national regulations.
Hazard-determining components for labeling
- Contains: Trimethoxysilane.
Adhesive and Sealant Based on MS Polymer
With its high initial adhesion, the product is suitable for wall and ceiling mounting of mirrors, curtain rails, lights, as well as heavy parts made of stone, concrete, glass, metal, wood, and plastic.
Once the adhesive and sealant has set, it remains permanently elastic, making it excellent for expansion joints. This is particularly important for outdoor use, to compensate for expansions and stresses in flooring and wall coverings, for example.
Whether it's acid rain, saltwater, chlorinated water, or household cleaners, the product impresses with high resistance and does not discolor. Dirt hardly sticks and can always be easily removed.
Thanks to UV resistance, joint sealings and adhesive spots do not become brittle or crumbly. Moreover, the adhesive and sealant is resistant to extreme cold down to -40 °C and heat up to +100 °C (briefly even up to +120 °C).
The product is resistant to mold and bacteria.
This adhesive and sealant is free of silicone, solvents, and contains no diisocyanates, which are often triggers for respiratory diseases.
MS Polymer-Based Adhesive and Sealant
Even without surface treatment with adhesion primers, excellent adhesion is achieved. The product can be used wet-on-wet, is overpaintable and compatible with paint.
Once the adhesive and sealant has cured, it remains permanently elastic, making it ideal for expansion joints. This is particularly important for outdoor use to accommodate expansions and tensions in floor and wall coverings.
Whether acid rain, salt water, chlorinated water, or household cleaners, the product impresses with its high resistance and does not discolor. Dirt does not stick and can always be easily removed.
Due to its UV resistance, joint seals and adhesive spots do not become brittle or crumbly. Moreover, the adhesive and sealant withstands extreme cold down to -40 °C and heat up to +100 °C (briefly even up to +130 °C).
The product is resistant to mold and bacteria. Therefore, it is also suitable for use in humid-warm environmental conditions.
This adhesive and sealant is free of silicone, solvents, and contains no diisocyanates, which are often triggers for respiratory diseases.
The adhesive and sealant can be processed on both dry and wet surfaces and even directly underwater.
MS Polymer-Based Adhesive and Sealant
Even without surface treatment with adhesion primers, excellent adhesion is achieved. The product can be used wet-on-wet, is overpaintable and compatible with paint.
Once the adhesive and sealant has cured, it remains permanently elastic, making it ideal for expansion joints. This is particularly important for outdoor use to accommodate expansions and tensions in floor and wall coverings.
Whether acid rain, salt water, chlorinated water, or household cleaners, the product impresses with its high resistance and does not discolor. Dirt does not stick and can always be easily removed.
Due to its UV resistance, joint seals and adhesive spots do not become brittle or crumbly. Moreover, the adhesive and sealant withstands extreme cold down to -40 °C and heat up to +100 °C (briefly even up to +130 °C).
The product is resistant to mold and bacteria. Therefore, it is also suitable for use in humid-warm environmental conditions.
This adhesive and sealant is free of silicone, solvents, and contains no diisocyanates, which are often triggers for respiratory diseases.
The adhesive and sealant can be processed on both dry and wet surfaces and even directly underwater.
Heat-Resistant Adhesive and Sealant
The product's heat resistance ranges from -40 °C to +100 °C, and even up to +200 °C for short periods. This extends its application to heating and stove construction, as well as to metal parts that are bonded and then finished in a curing oven with a powder coating.
Excellent adhesion is achieved even without surface treatment with adhesion primers. The product can be applied wet-on-wet, is paintable, and compatible with coatings.
Once the adhesive and sealant has set, it remains permanently elastic, making it excellent for expansion joints. This is especially important for outdoor use, for example, to compensate for expansions and tensions of floor and wall coverings.
Whether it's acid rain weathering, saltwater, chlorinated water, or household cleaners, the product impresses with its high resistance and does not discolor. Dirt practically does not stick to it and can always be easily removed.
Due to its UV resistance, joint sealants and adhesive spots do not become brittle or crumbly.
The product is resistant to mold and bacteria. Therefore, it is also suitable for use under humid-warm environmental conditions.
This adhesive and sealant is free from silicone, solvents, and contains no diisocyanates, which are often triggers for respiratory diseases.
Heat-Resistant Adhesive and Sealant
The product's heat resistance ranges from -40 °C to +100 °C, and even up to +200 °C for short periods. This extends its application to heating and stove construction, as well as to metal parts that are bonded and then finished in a curing oven with a powder coating.
Excellent adhesion is achieved even without surface treatment with adhesion primers. The product can be applied wet-on-wet, is paintable, and compatible with coatings.
Once the adhesive and sealant has set, it remains permanently elastic, making it excellent for expansion joints. This is especially important for outdoor use, for example, to compensate for expansions and tensions of floor and wall coverings.
Whether it's acid rain weathering, saltwater, chlorinated water, or household cleaners, the product impresses with its high resistance and does not discolor. Dirt practically does not stick to it and can always be easily removed.
Due to its UV resistance, joint sealants and adhesive spots do not become brittle or crumbly.
The product is resistant to mold and bacteria. Therefore, it is also suitable for use under humid-warm environmental conditions.
This adhesive and sealant is free from silicone, solvents, and contains no diisocyanates, which are often triggers for respiratory diseases.
Heat-Resistant Adhesive and Sealant
The product's heat resistance ranges from -40 °C to +100 °C, and even up to +200 °C for short periods. This extends its application to heating and stove construction, as well as to metal parts that are bonded and then finished in a curing oven with a powder coating.
Excellent adhesion is achieved even without surface treatment with adhesion primers. The product can be applied wet-on-wet, is paintable, and compatible with coatings.
Once the adhesive and sealant has set, it remains permanently elastic, making it excellent for expansion joints. This is especially important for outdoor use, for example, to compensate for expansions and tensions of floor and wall coverings.
Whether it's acid rain weathering, saltwater, chlorinated water, or household cleaners, the product impresses with its high resistance and does not discolor. Dirt practically does not stick to it and can always be easily removed.
Due to its UV resistance, joint sealants and adhesive spots do not become brittle or crumbly.
The product is resistant to mold and bacteria. Therefore, it is also suitable for use under humid-warm environmental conditions.
This adhesive and sealant is free from silicone, solvents, and contains no diisocyanates, which are often triggers for respiratory diseases.
MS Polymer-Based Adhesive and Sealant
Even without surface treatment with adhesion primers, excellent adhesion is achieved. The product can be used wet-on-wet, is overpaintable and compatible with paint.
Once the adhesive and sealant has cured, it remains permanently elastic, making it ideal for expansion joints. This is particularly important for outdoor use to accommodate expansions and tensions in floor and wall coverings.
Whether acid rain, salt water, chlorinated water, or household cleaners, the product impresses with its high resistance and does not discolor. Dirt does not stick and can always be easily removed.
Due to its UV resistance, joint seals and adhesive spots do not become brittle or crumbly. Moreover, the adhesive and sealant withstands extreme cold down to -40 °C and heat up to +100 °C (briefly even up to +130 °C).
The product is resistant to mold and bacteria. Therefore, it is also suitable for use in humid-warm environmental conditions.
This adhesive and sealant is free of silicone, solvents, and contains no diisocyanates, which are often triggers for respiratory diseases.
The adhesive and sealant can be processed on both dry and wet surfaces and even directly underwater.
MS Polymer-Based Adhesive and Sealant
Even without surface treatment with adhesion primers, excellent adhesion is achieved. The product can be used wet-on-wet, is overpaintable and compatible with paint.
Once the adhesive and sealant has cured, it remains permanently elastic, making it ideal for expansion joints. This is particularly important for outdoor use to accommodate expansions and tensions in floor and wall coverings.
Whether acid rain, salt water, chlorinated water, or household cleaners, the product impresses with its high resistance and does not discolor. Dirt does not stick and can always be easily removed.
Due to its UV resistance, joint seals and adhesive spots do not become brittle or crumbly. Moreover, the adhesive and sealant withstands extreme cold down to -40 °C and heat up to +100 °C (briefly even up to +130 °C).
The product is resistant to mold and bacteria. Therefore, it is also suitable for use in humid-warm environmental conditions.
This adhesive and sealant is free of silicone, solvents, and contains no diisocyanates, which are often triggers for respiratory diseases.
The adhesive and sealant can be processed on both dry and wet surfaces and even directly underwater.